I am not a professional mechanic and I do not take any responsibility for any damage that occurs to your vehicle, person, home, property or pets. Also I am going by memory having done this a bout a year ago. Not only will the lights on your Altima be brighter, you decrease the likelihood you will need to change any of the bulbs again in the near future. You may want to read these suggestions through before you start. I left the store and hoped that I wouldn't have to return for another. When that bulb burned out, I couldn't tell what gear I was in at night. To gain access to the headlamp socket, you must remove the coolant resvoir on the passenger's side or the battery on the drivers side.
Now that you've verified that the new bulb works, go ahead and pop the plastic housing back into place. There are several plastic nubs that go into the car body… well I am getting ready to replace mine today and what the dealership told me was to replace the driver side I have to remove the air box and the air return just to get to the bulbs but after I do all of that I should be able to get to the bulbs just fine, or just bring it into the dealership and pay them 75 dollars to replace a bulb for me thanks… Hi there! You can access the bulbs easily from the trunk area, saving you the expense of having a mechanic replace the bulbs for you. To unscrew the bulb and connector from the housing, rotate it about half a turn in the counter clockwise direction. AnswerMike, I tried your advice, and it just doesn't work. Note: I am not a registered charity. There is a round plastic clip on the verticle carpet cover which must first be removed to access the back of the tail light assembly.
Then consult your owner's manual for the replacement procedure. The ring is located about 8 inches from either end of the car. See sources and related links below for replacement bulb information. I took the old bulb with me to Pep Boys and asked the guys at the counter which bulb number I needed to buy to replace it. Use of the replacement bulb size information is at your own risk.
On the other side you will need to remove the air filter box and connected parts. It may also be useful for owners of other Nissan or Infiniti made by Nissan Motors vehicles such as the Sentra, Maxima, the Infiniti G sedan, and the Infiniti M sedan. Move the bottle and place it in an upright position between the radiator and the dipstick if the engine is cold or on top of the grille by the… I am assuming you want to change the bulb and not the entire unit. . Twist and it should unlock.
First I had to pop out two snap rivets by using a flat head screw driver. Open the Trunk, and remove the carpeting from the left and right rear corners of the in inside of the trunk. Before you re-attach the bulb's connector to the housing, press the vehicle's brake pedal and test to see if the new light bulb illuminates. You can just twist the switch loose and pull out of bracket. I chose a long liife bulb rated at 12.
I took the old bulb with me to the Pep Boys auto parts store to buy a new one. There… Get a flash light and lay on the driver side floor board and look up at the brake pedal. See sources and related links below for replacement brake light bulb information. It is called a High Mount Stop Light. If you need to replace the third brake light bulb, click on the link at the beginning of this paragraph. It took a bit of wiggling to get the tail light assembly to pop off the car.
Feel free to use any replacement light bulb sizes that are listed on Modified Life but keep in mind that all information here is provided as is without any warranty of any kind. You may want to consider replacing both left and right at the same… I own a '98 Nissan Altima and couldn't figure it out on my own. If you are going to replace a bulb in your cluster, it is a good idea to replace all of them. The replacement light bulbs with their part numbers are as follows: Brake , Rear Turn Signal and Reverse Light. Nissan has redesigned the 2001 Altima, so it's impossible for the layman to access the flange without special tools. Once again, I put a heavy box on the brake pedal and verified that all of the turn signal, reverse, and brake light bulbs were working properly. The last step is to have someone or something depress the brake pedal.
These bulbs should not be touched because the natural oils from fingers can ruin them! The rear turn signal light bulb is part number and the reverse light bulb is part number. As you can see, the inside of the glass is covered in a light black powder. This is a clear sign that the bulb has indeed reached the end of its useful life. Once the two nuts have been taken off, the assembly can be removed. I've had to take… I just had to do this on my own car. This is completely covered by the fascia of the bumper.
Then I loosened the 8mm nuts with an 8mm socket and ratcheting wrench. As simple as it sounds, the owner's manual is the best place to start for brake light bulb replacement instructions and illustrations. Turn the bulb socket counterclockwise to unlock it. I hope you found this guide useful. Turn the plastic cap counterclockwise and unlock it. See sources and related links below for replacement bulb information and full light bulb part numbers list. You can almost reach in behind the carpeting in the trunk and feel the two bolts that hold the integrated light assembly.
When I looked into quotes on my 2003 Altima headlights, I found out that there was a recall issue on the headlight assembly and they were going out too fast. Tools Used: Tools, Wrench set, Torque wrench, Replacement bulb Replace Brake Light Open the trunk of your Nissan Altima and locate the rear of the light assembly inside the trunk area. Please help support this website by shopping at. Then gently push on the housing with your hand and lift with the screw driver. You may need to push the rear window ledge downward slightly to free the tabs.